Marshall ElectronicsModel No. V-R261-DLW26" Full Resolution Dual Link / Waveform MonitorOperating Instructions
10Waveform Monitor ModeFull Screen Video Mode
11On-Screen MenuSTRUCTURE OVERVIEW
12On-Screen Menu (continued)MAIN MENU AND NAVIGATIONAccess and navigate the main menu using the RotoMenu™ knob:Using the RotoMenu knob• Press the Roto
13 16:9 MarkersUse this setting to superimpose one of 10 markers on the screen when in 16:9 or Full Screen mode. This setting isdisabled when the aspe
144:3 Marker Examples: Marker BackgroundUse this setting to choose how selected markers are displayed on the screen:• Off The marker is superimposed o
15Video Config SubmenuUse the Video Configuration submenu to select various video settings such as monochrome mode or blue-only mode. Monochrome ModeU
16 Pixel-to-Pixel ModeUse this setting to enable Pixel-to-Pixel mode.This mode bypasses the monitor’s internal scaling function and displays images in
17 Curtain ColorUse this setting to choose the default color displayed on the screen when no video input is present. Available colorsare blue, red, gr
18 HDMI CSC Auto (HDMI input only, via the DVI-I interface)The HDMI CSC Auto setting is used to accommodate newer HDMI interfaces that send colorspace
19 User-Definable Function ButtonsUse the Function 1, Function 2, Function 3 and Function 4 menu items to define each function button on the frontpane
2This page intentionally left blank
20OSD Config SubmenuUse the OSD Configuration submenu to select a variety of information to be displayed on the screen. IMD StateUse this setting to t
21 OSD TallyUse this setting to choose how tally is displayed on the screen. The available OSD Tally options depend on the TallySource selected in the
22 Anc. TimecodeUse this setting to enable time code display on the screen. Time code is de-embedded from the vertical ancillary data(VANC) within th
23IMD Config Submenu OverviewThe V-R261-DLW features an In-Monitor Display (IMD) with the ability to display on-screen text and tally in threecolors.
24. TSL v4.0Use the TSL v4.0 protocol setting when controlling the IMD from a TSL tally controller, or other controlling devicewhich utilizes the TSL
25 IMD Baud RateUse this setting to choose the baud rate. The baud rate must be set in conjunction with the controlling device. Availablebaud rates ar
26 IMD Fixed AlignUse this setting to choose the horizontal alignment of the IMD text. IMD text can be justified on the left, center or rightof the sc
27 608 ColorThe EIA-608 caption protocol can define the color for the closed caption text. Use this setting tochoose between using the color defined b
28• YUV Overlay The YUV components of the signal are overlaid.• RGB Parade The R (shown in Red), G (shown in Green) and B (shown in Blue) components o
29 Colorize WaveformUse the Colorize Waveform option to add or remove color from the Waveform display. When Colorize Waveform isON, the YUV and RGB da
3ContentsFeatures...
30 DID/SDIDUse this section to select which packet IDs should be counted on the DLW monitor display. For example, 0x6060would count the Timecode data
31SERVICE SUBMENU Software Version DisplayThe Main Board, Keypad, and FPGA software version numbers are displayed..The following information is displa
32Specifications PANELScreen Size 25.54” DiagonalDisplay Area (h x v) 528 mm x 375.6 mmAspect Ratio 16:10 Native (4:3/16:9 Modes)Pixels 1920 x RGB x 1
33Dimensions
34Maintenance Screen CleaningPeriodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-fiber
35This page intentionally left blank
36Marshall Electronics, Inc.1910 East Maple Ave.El Segundo, CA 90245Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688www.LCDRacks.com • sales@l
4FeaturesThe V-R261-DLW (Dual Link / Waveform) monitor is the latest addition to Marshall's expanding line of IMD-equippedmonitors. 1920 x 1200 F
5Installation and Initial Setup UnpackingCarefully unpack the V-R261-DLW monitor and verify that the following items are included:• V-R261-DLW Monitor
6Front Panel FeaturesPower ButtonTurn the monitor off or on by pressing the powerbutton. The LED on the power button is atmaximum illumination when th
7Rear Panel FeaturesRS-422/485 Serial InterfaceThe RS-422/485 ports are used to remotely controlthe IMD or all V-R261-DLW features, using a varietyof
8Compatible Input FormatsThe following SDI standards are supported by the V-R261-DLW:525i, 625i1035i (60 / 59.94)1080i (60 / 59.94 / 50)1080psF (24 /
9DLW Monitor LayoutsThe V-R261-DLW has 4 possible layouts, Multi mode, Vectorscope mode, Waveform mode and Full Screen Videomode. Each press of the LA
Comments to this Manuals